Search found 8 matches

by PaulEE
Sun 2019-11-17 9:57
Forum: Stand-Alone Applications
Topic: How to change fw on VS1103 module
Replies: 13
Views: 1128

Re: How to change fw on VS1103 module

Hello! Good news! After inquiring with a 'veteran' EE with much experience in low-level embedded programming, I found that defining new defaults was as simple as editing file c1103.s, I have successfully gotten the standalone player to pause and wait for a new song selection and play request. For th...
by PaulEE
Fri 2019-11-15 19:49
Forum: Stand-Alone Applications
Topic: How to change fw on VS1103 module
Replies: 13
Views: 1128

Re: How to change fw on VS1103 module

Still wondering how to set the default behavior to pause before play. Any help appreciated.

Thank you,
Paul
by PaulEE
Thu 2019-11-14 22:12
Forum: Stand-Alone Applications
Topic: How to change fw on VS1103 module
Replies: 13
Views: 1128

Re: How to change fw on VS1103 module

Success!! The latest solution update made easy work in getting the audio to play! I think I got it from here - simple serial commands to dictate behavior of module..! I have one other question (until I think of another in month ;) ): Is the file C1103.s the place I would tell the module to default t...
by PaulEE
Thu 2019-11-14 19:17
Forum: Stand-Alone Applications
Topic: How to change fw on VS1103 module
Replies: 13
Views: 1128

Re: How to change fw on VS1103 module

Excellent, yes. Makes sense. I will try this later today after I get some high-priority fires put out :) When I changed sdplayer to vcc and left the other lcc, it compiled. When I changed both sdplayer and spiplayer both to lcc, it threw errors...so I went back to lcc. If the new solution from a pos...
by PaulEE
Thu 2019-11-14 1:27
Forum: Stand-Alone Applications
Topic: How to change fw on VS1103 module
Replies: 13
Views: 1128

Re: How to change fw on VS1103 module

Good evening! (morning!), I have begun with fresh files, opened VSIDE, added -x 0x30 to the two post-build steps for each sub-project, and compiled (lcc worked). I do get 0.60I (capital letter "I" there) upon boot, and then the module sends out a constant stream of "c". I do not see "SD" on the init...
by PaulEE
Wed 2019-11-13 3:09
Forum: Stand-Alone Applications
Topic: How to change fw on VS1103 module
Replies: 13
Views: 1128

Re: How to change fw on VS1103 module

Alright, so I have located and loaded sdeeprom.img: pcmodflash -l sdeeprom.img -p 3 -sm 4 It successfully programmed the part, or so it says... "SPI Programming Successful! Programming Finished Successfully 11 blocks programmed in 54 seconds, 0.10 kB/sec" When I open the COM3 port @ 9,600 baud and d...
by PaulEE
Wed 2019-11-13 2:48
Forum: Stand-Alone Applications
Topic: How to change fw on VS1103 module
Replies: 13
Views: 1128

Re: How to change fw on VS1103 module

Hi, There seems to be a small difference between the VSIDE solution and the Linux development setup. Looking at the post-build command on the sdmodule project, it creates a file sdeeprom.img . Try programming that with pcflash. (The VSIDE prommer defaults to "eeprom.img", so the spiplayer project c...
by PaulEE
Thu 2019-10-31 2:42
Forum: Stand-Alone Applications
Topic: How to change fw on VS1103 module
Replies: 13
Views: 1128

Re: How to change fw on VS1103 module

Hello, If someone could please point me in the right direction, I'd appreciate it. I want to do precisely with the original poster wanted to do. I have a few WAV files on a 2 GB SD card. I want to use PCMODFLASH to put the correct firmware on the VS1103MOD board and control the device via UART (even...