Audible "Hello" example for VS1003B + Microcontroller

Writing software for systems that use VLSI Solution's devices as slave codecs to a host microcontroller.

Audible "Hello" example for VS1003B + Microcontroller

Postby Panu » Mon 2010-10-18 11:54

Here is an example code for a microcontroller and a VS1003B chip, which says "Hello" repeatedly on the VS1003B. For easy compiling, this is a single .c file, which contains all the necessary definitions, except register definitions of the AT89C51ED2/RD2 microcontroller, to which this is targeted. The "Hello" word comes from a small bitrate MP3 file, which is included as an array of 1695 bytes.

Now, all the microcontroller specific stuff is in the beginning (mostly SPI transfer functions) so it should be quite easy to port to other microcontrollers. This one was written for the SDCC compiler, which uses the "code" reserved word to put arrays in the code ROM. Your compiler is probably different.

This code is free for use for all purposes with one requirement: If you succesfully port this code to another microcontroller, you are honor-bound to reply to this post and attach your code! :D

Looking forward to hearing about you success!...

-Panu

P.S.
- For VS1011, change the CLOCKF value to 0x9800.
- For VS1053, change the CLOCKF value to 0x8800, and please check from the datasheet of VS1053 for the procedures about what is the proper way to send data to VS1053.

Code: Select all
// VS1003B   VS1003B   VS1003B   VS1003B   VS1003B   VS1003B   VS1003B //

// PKP: Hello, World code for VS1003B and AT89C51RD2 microcontroller

// Compiles with:
// sdcc2-4-0/bin/sdcc --model-small hello.c


//// ------- Microcontroller Specific Code Starts ------- ////
#include "AT89C51ED2-SFR.h" // Import microcontroller register definitions.


// Pin connections //

/** Chip Reset Pin */
#define MP3_XRESET P2_4

/** Control Chip Select Pin (for accessing SPI Control/Status registers) */
#define MP3_XCS P2_3

/** Data Chip Select / BSYNC Pin */
#define MP3_XDCS P2_5

//** Data Request Pin: Player asks for more data */
#define MP3_DREQ P3_4


/** Macro to pull a GPIO pin high */
#define SET_HIGH(a){(a)=1;}

/** Macro to pull a GPIO pin low */
#define SET_LOW(a){(a)=0;}


// SPI bus operations //

/** switch to fast SPI Clock */
#define SPISetFastClock(){SPCON=0x71;} 

/** Start sending a byte to SPI */
#define SPIPutCharWithoutWaiting(c){SPDAT=(c);}

/** Wait for SPI ready to send a new character (previous has been sent) */
#define SPIWait(){while(!(SPSTA & 0x80));;}

/** Wait for SPI ready, then initiate character sending */
#define SPIPutChar(c){SPIWait();SPDAT=(c);}

/** SPI data return register of AT89C51RD2 hardware*/
#define SPI_RESULT_BYTE SPDAT

/** Send 8 ones to SPI bus and receive the result byte. */
unsigned char SPIGetChar(){
  SPIPutCharWithoutWaiting(0xff); /* send 0xff */
  SPIWait(); /* wait for the byte to transfer */
  return SPI_RESULT_BYTE; /* Return the received byte */
}

// Initialize SPI, set slow SPI clock
void InitSPI() { 
  SPCON  = 0xF2;    /* Set slow spi clock        */
  /* Send dummy SPI byte to initialize SPI */
  SPIPutCharWithoutWaiting(0xFF);
}


// Microcontroller specific init
void InitMicrocontroller() {
  CKCON0 = 0x01;    /* CPU x 2, timer2 x 1       */
  IEN0   = 0;       /* Disable all interrupts    */
  InitSPI();
}


void SmallDelay(unsigned long delay) {
  volatile unsigned long d;
  while(delay--) {
    d=delay;
  }
}

void Delay(unsigned long milliseconds){
  SmallDelay(milliseconds*100);
}



//// -------- Microcontroller Specific Code Ends ------- ////
// Most microcontrollers should not need (many) changes to the code below...



// VS10XX Operations //



/** VS10xx SCI Write Command byte is 0x02 */
#define VS_WRITE_COMMAND 0x02

/** VS10xx SCI Read Command byte is 0x03 */
#define VS_READ_COMMAND 0x03

/** Put the MP3 player chip in reset */
#define Mp3PutInReset(){SET_LOW(MP3_XRESET);}

/** Release the MP3 player chip from reset */
#define Mp3ReleaseFromReset(){SET_HIGH(MP3_XRESET);}

/** Pull the VS10xx Control Chip Select line Low */
#define Mp3SelectControl(){SET_LOW(MP3_XCS);}

/** Pull the VS10xx Control Chip Select line High */
#define Mp3DeselectControl(){SET_HIGH(MP3_XCS);}

/** Pull the VS10xx Data Chip Select line Low */
#define Mp3SelectData(){SET_LOW(MP3_XDCS);}

/** Pull the VS10xx Data Chip Select line High */
#define Mp3DeselectData(){SET_HIGH(MP3_XDCS);}


/** VS10xx SCI Registers */
#define SPI_MODE   0x0   /**< VS10xx register */
#define SPI_STATUS   0x1   /**< VS10xx register */
#define SPI_BASS   0x2   /**< VS10xx register */
#define SPI_CLOCKF   0x3   /**< VS10xx register */
#define SPI_DECODE_TIME   0x4   /**< VS10xx register */
#define SPI_AUDATA   0x5   /**< VS10xx register */
#define SPI_WRAM   0x6   /**< VS10xx register */
#define SPI_WRAMADDR   0x7   /**< VS10xx register */
#define SPI_HDAT0   0x8   /**< VS10xx register */
#define SPI_HDAT1   0x9   /**< VS10xx register */
#define SPI_AIADDR   0xa   /**< VS10xx register */
#define SPI_VOL      0xb   /**< VS10xx register */
#define SPI_AICTRL0   0xc   /**< VS10xx register */
#define SPI_AICTRL1   0xd   /**< VS10xx register */
#define SPI_AICTRL2   0xe   /**< VS10xx register */
#define SPI_AICTRL3   0xf   /**< VS10xx register */


/** Write VS10xx register */
#define Mp3WriteRegister(addressbyte,highbyte,lowbyte){ \
Mp3DeselectData(); \
Mp3SelectControl(); \
SPIPutCharWithoutWaiting(VS_WRITE_COMMAND); \
SPIPutChar((addressbyte)); \
SPIPutChar((highbyte)); \
SPIPutChar((lowbyte)); \
SPIWait(); \
Mp3DeselectControl();}


/** Read the 16-bit value of a VS10xx register */
unsigned int Mp3ReadRegister (unsigned char addressbyte){
  unsigned int resultvalue = 0;
  Mp3DeselectData();
  Mp3SelectControl();
  SPIPutCharWithoutWaiting(VS_READ_COMMAND);
  SPIPutChar((addressbyte));
  SPIPutChar(0xff);
  SPIWait();
  resultvalue = (SPI_RESULT_BYTE) << 8;
  SPIPutCharWithoutWaiting(0xff);
  SPIWait();
  resultvalue |= (SPI_RESULT_BYTE);
  Mp3DeselectControl();
  return resultvalue;
}



/** Set VS10xx Volume Register */
#define Mp3SetVolume(leftchannel,rightchannel){\
Mp3WriteRegister(11,(leftchannel),(rightchannel));}

/** Soft Reset of VS10xx (Between songs) */
void Mp3SoftReset(){
  Mp3WriteRegister (SPI_MODE, 0x08, 0x04); /* Newmode, Reset, No L1-2 */
  Delay(1); /* One millisecond delay */
  while (!MP3_DREQ) /* wait for startup */
    ;
  /* Set clock register, doubler etc. */
  Mp3WriteRegister(SPI_CLOCKF, 0xb3, 0xfe);
  Delay(1); /* One millisecond delay */
  /* Wait for DREQ */
  while (!MP3_DREQ)
    ;
}

/** Reset VS10xx */
void Mp3Reset(){
  Mp3PutInReset();
  Delay(1);
  InitSPI();
  /* Un-reset MP3 chip */
  Mp3DeselectControl();
  Mp3DeselectData();
  Mp3ReleaseFromReset();
  Mp3SetVolume(0xff,0xff); //Declick: Immediately switch analog off
 
  /* Declick: Slow sample rate for slow analog part startup */
  Mp3WriteRegister(SPI_AUDATA, 0, 10); /* 10 Hz */
  Delay(100);
  /* Switch on the analog parts */
  Mp3SetVolume(0xfe,0xfe);
  Mp3WriteRegister (SPI_AUDATA, 31, 64); /* 8kHz */

  Mp3SetVolume(20,20); // Set initial volume (20 = -10dB)
  Mp3SoftReset();
  SPISetFastClock(); // Now you can set high speed SPI clock
}


// The spoken word "Hello" as an MP3 file.
code const unsigned char HelloMP3[] = { // Note: "code" in AT89C51 SDCC means to put this array into ROM.
  0xFF,0xF2,0x40,0xC0,0x19,0xB7,0x00,0x14,0x02,0xE6,0x5C, /* ..@.......\ */
  0x01,0x92,0x68,0x01,0xF1,0x5E,0x03,0x08,0xF0,0x24,0x80, /* ..h..^...$. */
  0x05,0x9E,0x20,0xC6,0xFC,0x12,0x32,0x5C,0xBF,0xF9,0xB9, /* .. ...2\... */
  0x20,0x4A,0x7F,0x85,0xEC,0x4C,0xCD,0xC7,0x27,0xFE,0x5C, /*  J...L..'.\ */
  0x34,0x25,0xCB,0xE6,0xFF,0xFF,0x8E,0x42,0xE1,0xA0,0x5E, /* 4%.....B..^ */
  0xCA,0x6E,0x30,0x9F,0xFF,0xF8,0xC2,0x12,0x84,0xB9,0x7C, /* .n0.......| */
  0xDC,0x61,0x09,0x4A,0x7F,0xFF,0xFF,0xF9,0x7D,0x32,0x51, /* .a.J....}2Q */
  0x09,0x7C,0xE1,0xA5,0x6E,0xB4,0xFF,0xFF,0xFF,0xFF,0xD3, /* .|..n...... */
  0x34,0x41,0x91,0xF0,0x11,0x8F,0x00,0x0F,0x81,0x9C,0x10, /* 4A......... */
  0xEE,0x59,0xCE,0x56,0x67,0xFF,0xF2,0x42,0xC0,0xEC,0x53, /* .Y.Vg..B..S */
  0x09,0x15,0xF9,0xAA,0xA8,0x0D,0xD9,0x40,0x00,0xCA,0x34, /* .......@..4 */
  0x53,0xD9,0x18,0xAB,0x7D,0xF7,0x89,0x3F,0x11,0x38,0x94, /* S...}..?.8. */
  0x82,0x59,0x93,0x20,0x6A,0x0C,0xEE,0x8E,0x58,0xFA,0x38, /* .Y. j...X.8 */
  0x82,0xCA,0xF0,0x58,0xBB,0xDA,0x0C,0x50,0x56,0x1F,0xBB, /* ...X...PV.. */
  0x18,0x5D,0x8B,0x9F,0xDA,0x71,0x4F,0xFF,0xBD,0xFE,0xEF, /* .]...qO.... */
  0x69,0x36,0x86,0x3C,0x50,0xBB,0x0A,0x07,0x89,0x54,0xF0, /* i6.<P....T. */
  0x88,0x9F,0x90,0x95,0x30,0x94,0x2E,0x7E,0xF0,0x64,0x96, /* ....0..~.d. */
  0x79,0x08,0x3E,0x20,0x97,0x28,0x34,0x9C,0x09,0x7F,0xD2, /* y.> .(4.... */
  0xC0,0x01,0x75,0xF8,0x05,0x6B,0x5F,0x41,0x17,0x0B,0xE7, /* ..u..k_A... */
  0xFF,0xF2,0x40,0xC0,0x61,0xE5,0x0B,0x16,0x09,0xC6,0xC5, /* ..@.a...... */
  0x74,0x7B,0xCC,0x94,0x7A,0xF7,0x80,0x76,0xB2,0xD2,0xF8, /* t{..z..v... */
  0x39,0x06,0x38,0xFD,0x71,0xC5,0xDE,0x3A,0x38,0xBF,0xD5, /* 9.8.q..:8.. */
  0xF7,0x12,0x37,0xCB,0xF5,0x63,0x0C,0x9B,0xCE,0x77,0x25, /* ..7..c...w% */
  0xED,0xFB,0x3D,0x6B,0x35,0xF9,0x6D,0xD7,0xF9,0x2C,0xD1, /* ..=k5.m..,. */
  0x97,0x15,0x87,0x93,0xA4,0x49,0x4A,0x18,0x16,0x07,0xA1, /* .....IJ.... */
  0x60,0xF7,0x52,0x94,0xDB,0x02,0x16,0x70,0xB2,0xD8,0x80, /* `.R....p... */
  0x30,0xC2,0x94,0x40,0x81,0x74,0x5A,0x19,0x7A,0x80,0x60, /* 0..@.tZ.z.` */
  0x41,0x21,0x46,0x95,0xD5,0xC4,0x40,0xD2,0x01,0xC0,0x01, /* A!F...@.... */
  0xDA,0xD9,0xA0,0xB1,0x01,0xFF,0xF2,0x42,0xC0,0x82,0x10, /* .......B... */
  0x0B,0x12,0xF9,0x9E,0xC9,0x7E,0x7A,0xC6,0x95,0x55,0x09, /* .....~z..U. */
  0x8B,0x19,0x5E,0x8B,0x26,0xCA,0xEB,0x68,0x8A,0x05,0x8F, /* ..^.&..h... */
  0x36,0xA5,0xA5,0x03,0xB8,0x9C,0xED,0x24,0x51,0x59,0x90, /* 6......$QY. */
  0xF6,0xC5,0x7D,0xB5,0xAD,0xAF,0xF6,0x3B,0x18,0xEF,0x3F, /* ..}....;..? */
  0xFF,0xFF,0x4E,0xDE,0x16,0x66,0x0B,0xAA,0x33,0x23,0xDD, /* ..N..f..3#. */
  0x9C,0x4E,0x6E,0x55,0x22,0x9D,0xA2,0x40,0xA6,0x36,0x31, /* .NnU"..@.61 */
  0x69,0xA5,0xE1,0xD9,0x7F,0xF7,0xC6,0xCC,0x48,0x00,0x0E, /* i.......H.. */
  0x90,0x16,0x00,0x0F,0xDE,0x6E,0x80,0x11,0x0C,0x9A,0x4F, /* .....n....O */
  0x56,0xDB,0x88,0xD3,0xB2,0x1C,0x00,0xE0,0x2E,0x3E,0xAC, /* V........>. */
  0xFF,0xF2,0x40,0xC0,0x1C,0xE5,0x19,0x13,0x31,0x4E,0xCD, /* ..@.....1N. */
  0x9E,0xC3,0x06,0x71,0x03,0x85,0xE5,0xB5,0x6D,0x88,0x50, /* ...q....m.P */
  0x8E,0x0E,0x17,0x3B,0x19,0xFB,0x4E,0x3B,0x99,0xEF,0x4C, /* ...;..N;..L */
  0x9E,0xF7,0x7B,0x31,0x7C,0x3C,0x5F,0xFF,0xF4,0xF8,0xE3, /* ..{1|<_.... */
  0x92,0x42,0x07,0x8E,0x83,0x8E,0x0F,0x05,0x08,0x91,0xA3, /* .B......... */
  0x16,0xE2,0xDF,0xB7,0x62,0x60,0x48,0x31,0x3C,0xFF,0xD4, /* ....b`H1<.. */
  0x9E,0x0C,0x68,0x00,0x77,0x54,0xE3,0x1E,0x05,0xC5,0xF8, /* ..h.wT..... */
  0xEA,0x8D,0x82,0x9D,0x08,0xA9,0x06,0x8D,0x1E,0x5D,0x7C, /* .........]| */
  0x7F,0x08,0xC0,0x50,0x45,0x42,0xD0,0x36,0xF8,0xB2,0x4D, /* ...PEB.6..M */
  0x53,0x0C,0x80,0x3B,0x4D,0xFF,0xF2,0x42,0xC0,0x2F,0x3C, /* S..;M..B./< */
  0x25,0x19,0x29,0xFE,0xBC,0x2E,0xC4,0xD0,0x99,0x4C,0x48, /* %.)......LH */
  0xB0,0x9C,0x49,0xD2,0x1A,0x2D,0x02,0xC2,0x79,0x69,0x16, /* ..I..-..yi. */
  0x92,0xA8,0xC5,0xAB,0x45,0x5A,0x68,0xE8,0x75,0x57,0xCD, /* ....EZh.uW. */
  0xF1,0xB9,0xAA,0x13,0x88,0xE4,0x87,0x42,0x15,0xB3,0x58, /* .......B..X */
  0xF5,0xA3,0x46,0xB1,0xCF,0xD3,0x59,0x7E,0xBA,0xB5,0xA7, /* ..F...Y~... */
  0x6B,0x0B,0x17,0x57,0x6B,0x5C,0x4A,0xCD,0x53,0x76,0x2A, /* k..Wk\J.Sv* */
  0x1D,0x28,0xC5,0x1C,0x76,0x5C,0xDD,0x0A,0x00,0x4B,0xC0, /* .(..v\...K. */
  0x1B,0xCA,0xA8,0xE9,0x81,0x5B,0xA6,0xDC,0xA4,0x59,0x13, /* .....[...Y. */
  0xFC,0xBA,0x8F,0x98,0x79,0x44,0x25,0xC9,0x35,0x38,0xCA, /* ....yD%.58. */
  0xFF,0xF2,0x40,0xC0,0xB9,0x7D,0x1A,0x13,0x79,0x6A,0xC8, /* ..@..}..yj. */
  0x3E,0xC4,0x46,0x94,0x8D,0x3C,0x67,0x85,0xB1,0xA8,0x89, /* >.F..<g.... */
  0xC0,0xF2,0xE6,0x2F,0x9D,0x7C,0xC9,0xB4,0xBE,0xCF,0xE1, /* .../.|..... */
  0x7D,0xFE,0x1F,0x03,0x00,0x12,0x84,0x72,0x8C,0xE7,0xD8, /* }......r... */
  0x5E,0xC9,0xA9,0x01,0xBA,0x9B,0xC4,0x10,0x5C,0x70,0x2E, /* ^.......\p. */
  0x6C,0x48,0xE7,0x8C,0x15,0x0B,0x06,0x01,0xE5,0xFF,0xFF, /* lH......... */
  0xD4,0x0D,0x00,0x0F,0xCE,0x58,0x95,0x61,0xA8,0x9E,0x7B, /* .....X.a..{ */
  0x19,0x98,0xB0,0xF0,0xC6,0x72,0x82,0xD5,0x27,0x06,0x47, /* .....r..'.G */
  0x41,0x22,0x0F,0x65,0x93,0xC9,0x8A,0x09,0x19,0x48,0x1B, /* A".e.....H. */
  0xBD,0xD6,0x64,0x1A,0xAC,0xFF,0xF2,0x42,0xC0,0xF1,0x11, /* ..d....B... */
  0x25,0x14,0x22,0x06,0xBC,0x0E,0xD4,0x4E,0x99,0x90,0xA8, /* %."....N... */
  0xD8,0xB7,0xAD,0x5D,0x3E,0xAF,0x6E,0xBE,0x66,0x83,0xA4, /* ...]>.n.f.. */
  0xE3,0xC2,0xE0,0x29,0x43,0x87,0x5F,0x4F,0x27,0x9C,0x2C, /* ...)C._O'., */
  0xD0,0x91,0xF3,0x87,0x9B,0x54,0xED,0xD1,0xB4,0xF3,0x39, /* .....T....9 */
  0x87,0x22,0x06,0x86,0x0D,0x71,0xE4,0x6F,0x2A,0x08,0x04, /* ."...q.o*.. */
  0xC0,0x03,0x2A,0xB1,0xE2,0x05,0x4D,0x64,0xA1,0x9C,0xA6, /* ..*...Md... */
  0x0D,0x41,0xA6,0xF2,0x7A,0xC1,0x30,0xC3,0x38,0x26,0x09, /* .A..z.0.8&. */
  0x50,0x08,0xC4,0xF6,0x30,0x0C,0xA6,0xA9,0x17,0x00,0x13, /* P...0...... */
  0x0C,0xDC,0xC4,0x2F,0x28,0xEB,0x3F,0xCD,0x7A,0x3D,0x2F, /* .../(.?.z=/ */
  0xFF,0xF2,0x40,0xC0,0x18,0x6F,0x2E,0x13,0xA1,0xF2,0xBC, /* ..@..o..... */
  0x36,0xCB,0x4E,0x99,0x6E,0xFC,0xEE,0xC5,0xF0,0xA0,0xB7, /* 6.N.n...... */
  0x92,0xD4,0xEE,0x79,0x7C,0x50,0x5D,0xE5,0x04,0x94,0xA9, /* ...y|P].... */
  0x76,0xCF,0x6C,0x70,0xDD,0x0D,0xD4,0xEE,0xED,0x98,0xE8, /* v.lp....... */
  0xC8,0x35,0x36,0x7A,0x0C,0x05,0x80,0x03,0xBC,0xBE,0x91, /* .56z....... */
  0x00,0x7C,0xAE,0x65,0xB8,0x91,0xA3,0x33,0xBA,0x68,0x60, /* .|.e...3.h` */
  0xD4,0x1A,0x66,0xF8,0x43,0xA0,0x20,0x89,0xE7,0x80,0xD8, /* ..f.C. .... */
  0x1E,0x4F,0xA0,0x04,0x60,0x06,0x0A,0xA4,0x91,0x24,0xFA, /* .O..`....$. */
  0x9F,0x57,0x53,0xF4,0x7A,0xDB,0x5F,0x56,0xE3,0x6E,0x0B, /* .WS.z._V.n. */
  0x8B,0x3A,0x1C,0xF9,0x5E,0xFF,0xF2,0x42,0xC0,0xB1,0x00, /* .:..^..B... */
  0x38,0x14,0x09,0xEE,0xB4,0x36,0xD3,0x4E,0x99,0xA4,0x78, /* 8....6.N..x */
  0x94,0x73,0xC4,0x66,0x30,0xF5,0xEA,0xDB,0xBA,0x67,0x67, /* .s.f0....gg */
  0x95,0x6B,0xAB,0x68,0x5D,0x08,0xA1,0x39,0x56,0xAB,0x1E, /* .k.h]..9V.. */
  0xD5,0x03,0xE8,0x01,0x70,0x00,0xB3,0x93,0x33,0x19,0x8C, /* ....p...3.. */
  0x61,0x8F,0xBB,0x5D,0x24,0x12,0x63,0xD3,0x4B,0x5D,0x91, /* a..]$.c.K]. */
  0x08,0x43,0x22,0x56,0x1A,0xC5,0x10,0x21,0x84,0xA8,0xEA, /* .C"V...!... */
  0x80,0xBF,0x16,0x8E,0x3D,0x46,0x18,0x9C,0x6E,0x9A,0x91, /* ....=F..n.. */
  0xE6,0xC9,0x6F,0xD2,0x7D,0x27,0xD7,0xE9,0x6B,0xFF,0x0A, /* ..o.}'..k.. */
  0x03,0x43,0x89,0xD5,0xBF,0x52,0x97,0x0A,0x25,0x95,0x0D, /* .C...R..%.. */
  0xFF,0xF2,0x40,0xC0,0xF5,0xC3,0x41,0x13,0x81,0xEE,0xA8, /* ..@...A.... */
  0x5E,0xD3,0x44,0x98,0xFC,0xCF,0x97,0xF9,0x58,0xB5,0x33, /* ^.D.....X.3 */
  0xB1,0x85,0x47,0x86,0xD7,0x98,0x01,0x3B,0xA3,0x4F,0x7E, /* ..G....;.O~ */
  0x04,0xA6,0xC3,0x39,0x21,0x70,0x27,0x62,0xB5,0x18,0x10, /* ...9!p'b... */
  0x09,0x99,0x00,0x8B,0x7E,0xF2,0xBF,0x52,0x18,0x26,0x30, /* ....~..R.&0 */
  0x1C,0xB0,0x01,0x49,0x30,0xE0,0xC3,0x11,0x46,0x05,0xCC, /* ...I0...F.. */
  0x49,0x14,0x28,0xB2,0xED,0x4B,0x57,0x5A,0x2F,0xB7,0x46, /* I.(..KWZ/.F */
  0x63,0x34,0xD2,0xDA,0x9F,0x56,0x32,0xB7,0xA2,0x25,0xFF, /* c4...V2..%. */
  0x94,0x28,0x33,0x7F,0x3B,0xC4,0x50,0xEC,0xB1,0xE2,0x26, /* .(3.;.P...& */
  0xA1,0xB7,0x07,0x7F,0xFB,0xFF,0xF2,0x42,0xC0,0x67,0x6A, /* .......B.gj */
  0x4C,0x13,0xF9,0x6A,0x90,0x7E,0xDB,0x44,0x94,0x3F,0xFF, /* L..j.~.D.?. */
  0x14,0xD6,0x2A,0xFF,0xFF,0xC1,0x34,0x8C,0x48,0x22,0x00, /* ..*...4.H". */
  0x06,0x8F,0x21,0xFD,0x64,0x60,0x04,0x92,0x42,0xEA,0x74, /* ..!.d`..B.t */
  0x32,0x37,0xAA,0x5A,0x9F,0x67,0x01,0x8B,0x3F,0x37,0x31, /* 27.Z.g..?71 */
  0xDD,0x06,0x3C,0x01,0x34,0x30,0xE0,0x5C,0x78,0x78,0xCB, /* ..<.40.\xx. */
  0xD6,0xF1,0x31,0x8A,0x69,0x61,0x93,0x92,0x42,0xCE,0x4B, /* ..1.ia..B.K */
  0xC5,0x02,0x4E,0x73,0xC6,0x24,0x30,0xCD,0x08,0x66,0xC6, /* ..Ns.$0..f. */
  0x35,0xAB,0xA2,0x3D,0x2F,0xB3,0xBD,0x34,0x87,0x13,0xEE, /* 5..=/..4... */
  0x71,0x45,0x68,0xFA,0xEA,0x05,0x84,0x41,0x36,0x4C,0x9A, /* qEh....A6L. */
  0xFF,0xF2,0x40,0xC0,0xC9,0x92,0x56,0x13,0xD0,0x6E,0x70, /* ..@...V..np */
  0x54,0xD3,0xCC,0x28,0x06,0xD7,0x0E,0xA4,0x1D,0x9C,0x9D, /* T..(....... */
  0xD9,0xA9,0x88,0x7B,0xB5,0xA3,0x56,0xB7,0x4B,0x4B,0x5A, /* ...{..V.KKZ */
  0x9B,0x2C,0xA9,0xAD,0x6F,0x99,0x6C,0xC0,0x4C,0x14,0x14, /* .,..o.l.L.. */
  0xEF,0xB4,0x20,0x91,0x5F,0xBC,0x81,0x41,0x41,0x5D,0xD4, /* .. ._..AA]. */
  0x20,0xBD,0x05,0x1A,0x6F,0xE2,0x68,0x56,0x41,0x41,0x57, /*  ...o.hVAAW */
  0xF9,0xBF,0x89,0x82,0x8E,0xC7,0x8F,0x0A,0x0A,0x09,0x37, /* ..........7 */
  0xF1,0x05,0x0A,0x0A,0x0A,0x0A,0x09,0x05,0x37,0xFF,0x10, /* ........7.. */
  0x50,0x50,0x53,0x65,0xFF,0xFF,0xFD,0x75,0xDF,0xFF,0xFF, /* PPSe...u... */
  0x68,0x4F,0xFF,0x84,0x70,0xFF,0xF2,0x42,0xC0,0x27,0x50, /* hO..p..B.'P */
  0x5F,0x17,0xE8,0x82,0x3C,0x11,0x58,0x18,0x01,0x55,0x48, /* _...<.X..UH */
  0xBC,0x52,0xFC,0x4A,0x4C,0x3C,0xD5,0xF6,0x11,0x2D,0xBF, /* .R.JL<...-. */
  0xEA,0x03,0x5C,0x57,0x29,0xBF,0xC3,0x75,0x1C,0xE6,0xDD, /* ..\W)..u... */
  0xBF,0xED,0xEF,0xD0,0x98,0x77,0x71,0x95,0x73,0xFF,0xED, /* .....wq.s.. */
  0x54,0xBE,0xD5,0xEE,0xAE,0xC2,0xD5,0x0B,0xFF,0xF1,0x97, /* T.......... */
  0x8A,0xE4,0x42,0x09,0x99,0xB1,0xEA,0x94,0xDC,0x78,0xB5, /* ..B......x. */
  0x34,0x0F,0xF1,0x8F,0xFC,0x15,0xF6,0xFA,0xB1,0x47,0xA9, /* 4........G. */
  0x6C,0x67,0x43,0x8B,0xF2,0x76,0x22,0xED,0xDA,0x85,0xBA, /* lgC..v".... */
  0x2F,0xC7,0xF9,0xCF,0xFC,0xDB,0x46,0x2E,0x50,0x0A,0x84, /* /.....F.P.. */
  0xFF,0xF2,0x40,0xC0,0xC6,0x4A,0x59,0x28,0x2B,0x19,0xE0, /* ..@..JY(+.. */
  0x01,0x89,0x78,0x00,0x52,0x85,0x3C,0x8E,0x54,0x9A,0x48, /* ..x.R.<.T.H */
  0x5A,0x72,0x32,0x94,0xBF,0x43,0x4F,0x24,0x53,0x4B,0xEC, /* Zr2..CO$SK. */
  0x4B,0x99,0x0E,0x66,0x1F,0xFF,0xCE,0x7F,0xFF,0x3F,0x10, /* K..f.....?. */
  0xAE,0x82,0x62,0x71,0x34,0x18,0x59,0x9B,0x51,0xC7,0x59, /* ..bq4.Y.Q.Y */
  0xCE,0xEE,0xA5,0xFE,0x02,0xBB,0x30,0x91,0x49,0xD5,0x4B, /* ......0.I.K */
  0xF3,0xDC,0x9A,0xA9,0x57,0x8E,0x72,0x10,0xC0,0x5D,0x60, /* ....W.r..]` */
  0x67,0xFC,0x7D,0xD6,0xBA,0xDD,0xB3,0x8B,0x5A,0x0A,0x4C, /* g.}.....Z.L */
  0x41,0x4D,0x45,0x33,0x2E,0x39,0x33,0xAA,0xAA,0xAA,0xAA, /* AME3.93.... */
  0xAA,0xAA,0xAA,0xAA,0xAA,0x54,0x41,0x47,0x48,0x65,0x6C, /* .....TAGHel */
  0x6C,0x6F,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20, /* lo          */
  0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20, /*             */
  0x20,0x20,0x20,0x20,0x20,0x50,0x61,0x6E,0x75,0x2D,0x4B, /*      Panu-K */
  0x72,0x69,0x73,0x74,0x69,0x61,0x6E,0x20,0x50,0x6F,0x69, /* ristian Poi */
  0x6B,0x73,0x61,0x6C,0x6F,0x20,0x20,0x20,0x20,0x20,0x20, /* ksalo       */
  0x20,0x20,0x56,0x53,0x44,0x53,0x50,0x20,0x54,0x65,0x73, /*   VSDSP Tes */
  0x74,0x69,0x6E,0x67,0x20,0x20,0x20,0x20,0x20,0x20,0x20, /* ting        */
  0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20, /*             */
  0x20,0x20,0x20,0x4D,0x50,0x33,0x20,0x48,0x65,0x6C,0x6C, /*    MP3 Hell */
  0x6F,0x2C,0x20,0x57,0x6F,0x72,0x6C,0x64,0x21,0x20,0x20, /* o, World!   */
  0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20, /*             */
  0x00, /* . */
};


void main() {
  unsigned char *p;
  unsigned int i;

  InitMicrocontroller();
  Mp3Reset();


 
  while(1) {
    p = HelloMP3; // Point "p" to the beginning of array
    while (p <= &HelloMP3[sizeof(HelloMP3)-1]) {
      while (!MP3_DREQ) {
   // MP3 buffer is full, time to do something else...
   SPIWait(); // Wait until SPI transfer is completed
   Mp3DeselectData(); // Release the SDI bus
   // You can do something else here, the bus is free...
   // Maybe set the volume or whatever...
      }
      Mp3SelectData(); // Pull XDCS low
      SPIPutChar(*p++); // Send SPI byte
      // You can actually send 32 bytes here before checking for DREQ again
    }
 

    // End of file - send 2048 zeros before next file
    Mp3SelectData();
    for (i=0; i<2048; i++) {
      while (!MP3_DREQ)
   ; // wait here until DREQ is high again
      SPIPutChar(0);     
    }
    SPIWait(); // Wait until SPI transfer is completed
    Mp3DeselectData();

  } // Ok, time to send the hello file again.
 
}
Please reply to me.. it's awfully lonely here in the cold, dark cave with no lights..
Attachments
AT89C51ED2-SFR.h
(2.71 KiB) Downloaded 514 times
hello.c
(18.17 KiB) Downloaded 614 times
Info: Line In and Line Out, VS1000 User interface, Overlay howto, Latest VSIDE, MCU Howto, Youtube
Panu-Kristian Poiksalo, VLSI Solution Oy
User avatar
Panu
VLSI Staff. Currently on holiday.
 
Posts: 1481
Joined: Tue 2010-06-22 13:43

Re: Audible "Hello" example for VS1003B + Microcontroller

Postby RuiAlves » Tue 2010-11-02 16:05

I've ported this code to an arduino controller board using a VS1053 mp3 shield from sparkfun. Compile and upload using the arduino IDE.

Thanks Panu.

Cheers,
Rui

Code: Select all
//RA: Hello, World code for VS1053 and ATMega328 microcontroller on an arduino board
//Uses a sparkfun mp3 shield for arduino available at www.sparkfun.com

#include <SPI.h>

/** Control Chip Select Pin (for accessing SPI Control/Status registers) */
#define MP3_XCS 9

/** Data Chip Select / BSYNC Pin */
#define MP3_XDCS 2

//** Data Request Pin: Player asks for more data */
#define MP3_DREQ 3

/** VS10xx SCI Registers */
#define SPI_MODE 0x0   /**< VS10xx register */
#define SPI_STATUS 0x1   /**< VS10xx register */
#define SPI_BASS 0x2   /**< VS10xx register */
#define SPI_CLOCKF 0x3   /**< VS10xx register */
#define SPI_DECODE_TIME 0x4   /**< VS10xx register */
#define SPI_AUDATA 0x5   /**< VS10xx register */
#define SPI_WRAM 0x6   /**< VS10xx register */
#define SPI_WRAMADDR 0x7   /**< VS10xx register */
#define SPI_HDAT0 0x8   /**< VS10xx register */
#define SPI_HDAT1 0x9   /**< VS10xx register */
#define SPI_AIADDR 0xa   /**< VS10xx register */
#define SPI_VOL 0xb   /**< VS10xx register */
#define SPI_AICTRL0 0xc   /**< VS10xx register */
#define SPI_AICTRL1 0xd   /**< VS10xx register */
#define SPI_AICTRL2 0xe   /**< VS10xx register */
#define SPI_AICTRL3 0xf   /**< VS10xx register */

unsigned char SPIGetChar(){
  unsigned char returned = SPI.transfer(0xFF);
  return returned; /* Return the received byte */
}

/** Pull the VS10xx Control Chip Select line Low */
void Mp3SelectControl(){
  digitalWrite(MP3_XCS, LOW);
}

/** Pull the VS10xx Control Chip Select line High */
void Mp3DeselectControl(){
  digitalWrite(MP3_XCS, HIGH);
}

/** Pull the VS10xx Data Chip Select line Low */
void Mp3SelectData(){
  digitalWrite(MP3_XDCS, LOW);
}

/** Pull the VS10xx Data Chip Select line High */
void Mp3DeselectData(){
  digitalWrite(MP3_XDCS, HIGH);
}

void SPIWait(){
  while (!digitalRead(MP3_DREQ)){}; 
}

/** Write VS10xx register */
void Mp3WriteRegister(unsigned char addressbyte, unsigned char highbyte, unsigned char lowbyte){
  Mp3DeselectData();
  Mp3SelectControl();
  delay(1);
  SPI.transfer(0x02);  //write command
  SPI.transfer(addressbyte);
  SPI.transfer(highbyte);
  SPI.transfer(lowbyte);
  SPIWait();
  Mp3DeselectControl();
}

/** Read the 16-bit value of a VS10xx register */
unsigned int Mp3ReadRegister (unsigned char addressbyte){
  unsigned int resultvalue = 0;
  unsigned int aux = 0;
  Mp3DeselectData();
  Mp3SelectControl();
  SPI.transfer(0x03);  //read command
  SPI.transfer(addressbyte);
  aux = SPI.transfer(0xff);
  SPIWait();
  resultvalue = aux << 8;
  SPI.transfer(0xff);
  SPIWait();
  resultvalue |= aux;
  Mp3DeselectControl();
  return resultvalue;
}

/** Set VS10xx Volume Register */
void Mp3SetVolume(unsigned char leftchannel, unsigned char rightchannel){
  Mp3WriteRegister(SPI_VOL,leftchannel,rightchannel);
}

/** Soft Reset of VS10xx (Between songs) */
void Mp3SoftReset(){
  Mp3WriteRegister (SPI_MODE, 0x08, 0x04); /* Newmode, Reset, No L1-2 */
  delay(1); /* One millisecond delay */
  while (!digitalRead(MP3_DREQ)) /* wait for startup */
    ;
/* Set clock register, doubler etc. */
  Mp3WriteRegister(SPI_CLOCKF, 0xb3, 0xfe);
  delay(1); /* One millisecond delay */
/* Wait for DREQ */
  while (!digitalRead(MP3_DREQ))
    ;
   
    /***********************************ADDED AS TESTS*/
   
  Mp3DeselectControl();
  Mp3DeselectData();
  Mp3SetVolume(0xff,0xff); //Declick: Immediately switch analog off
   /* Declick: Slow sample rate for slow analog part startup */
  Mp3WriteRegister(SPI_AUDATA, 0, 10); /* 10 Hz */
  delay(100);
  /* Switch on the analog parts */
  Mp3SetVolume(0xfe,0xfe);
  Mp3WriteRegister (SPI_AUDATA, 31, 64); /* 8kHz */
  Mp3SetVolume(20,20); // Set initial volume (20 = -10dB)   
   
    /*******************************END ADDED AS TESTS*/   
}

unsigned char HelloMP3[] = {
  0xFF,0xF2,0x40,0xC0,0x19,0xB7,0x00,0x14,0x02,0xE6,0x5C, /* ..@.......\ */
  0x01,0x92,0x68,0x01,0xF1,0x5E,0x03,0x08,0xF0,0x24,0x80, /* ..h..^...$. */
  0x05,0x9E,0x20,0xC6,0xFC,0x12,0x32,0x5C,0xBF,0xF9,0xB9, /* .. ...2\... */
  0x20,0x4A,0x7F,0x85,0xEC,0x4C,0xCD,0xC7,0x27,0xFE,0x5C, /*  J...L..'.\ */
  0x34,0x25,0xCB,0xE6,0xFF,0xFF,0x8E,0x42,0xE1,0xA0,0x5E, /* 4%.....B..^ */
  0xCA,0x6E,0x30,0x9F,0xFF,0xF8,0xC2,0x12,0x84,0xB9,0x7C, /* .n0.......| */
  0xDC,0x61,0x09,0x4A,0x7F,0xFF,0xFF,0xF9,0x7D,0x32,0x51, /* .a.J....}2Q */
  0x09,0x7C,0xE1,0xA5,0x6E,0xB4,0xFF,0xFF,0xFF,0xFF,0xD3, /* .|..n...... */
  0x34,0x41,0x91,0xF0,0x11,0x8F,0x00,0x0F,0x81,0x9C,0x10, /* 4A......... */
  0xEE,0x59,0xCE,0x56,0x67,0xFF,0xF2,0x42,0xC0,0xEC,0x53, /* .Y.Vg..B..S */
  0x09,0x15,0xF9,0xAA,0xA8,0x0D,0xD9,0x40,0x00,0xCA,0x34, /* .......@..4 */
  0x53,0xD9,0x18,0xAB,0x7D,0xF7,0x89,0x3F,0x11,0x38,0x94, /* S...}..?.8. */
  0x82,0x59,0x93,0x20,0x6A,0x0C,0xEE,0x8E,0x58,0xFA,0x38, /* .Y. j...X.8 */
  0x82,0xCA,0xF0,0x58,0xBB,0xDA,0x0C,0x50,0x56,0x1F,0xBB, /* ...X...PV.. */
  0x18,0x5D,0x8B,0x9F,0xDA,0x71,0x4F,0xFF,0xBD,0xFE,0xEF, /* .]...qO.... */
  0x69,0x36,0x86,0x3C,0x50,0xBB,0x0A,0x07,0x89,0x54,0xF0, /* i6.<P....T. */
  0x88,0x9F,0x90,0x95,0x30,0x94,0x2E,0x7E,0xF0,0x64,0x96, /* ....0..~.d. */
  0x79,0x08,0x3E,0x20,0x97,0x28,0x34,0x9C,0x09,0x7F,0xD2, /* y.> .(4.... */
  0xC0,0x01,0x75,0xF8,0x05,0x6B,0x5F,0x41,0x17,0x0B,0xE7, /* ..u..k_A... */
  0xFF,0xF2,0x40,0xC0,0x61,0xE5,0x0B,0x16,0x09,0xC6,0xC5, /* ..@.a...... */
  0x74,0x7B,0xCC,0x94,0x7A,0xF7,0x80,0x76,0xB2,0xD2,0xF8, /* t{..z..v... */
  0x39,0x06,0x38,0xFD,0x71,0xC5,0xDE,0x3A,0x38,0xBF,0xD5, /* 9.8.q..:8.. */
  0xF7,0x12,0x37,0xCB,0xF5,0x63,0x0C,0x9B,0xCE,0x77,0x25, /* ..7..c...w% */
  0xED,0xFB,0x3D,0x6B,0x35,0xF9,0x6D,0xD7,0xF9,0x2C,0xD1, /* ..=k5.m..,. */
  0x97,0x15,0x87,0x93,0xA4,0x49,0x4A,0x18,0x16,0x07,0xA1, /* .....IJ.... */
  0x60,0xF7,0x52,0x94,0xDB,0x02,0x16,0x70,0xB2,0xD8,0x80, /* `.R....p... */
  0x30,0xC2,0x94,0x40,0x81,0x74,0x5A,0x19,0x7A,0x80,0x60, /* 0..@.tZ.z.` */
  0x41,0x21,0x46,0x95,0xD5,0xC4,0x40,0xD2,0x01,0xC0,0x01, /* A!F...@.... */
  0xDA,0xD9,0xA0,0xB1,0x01,0xFF,0xF2,0x42,0xC0,0x82,0x10, /* .......B... */
  0x0B,0x12,0xF9,0x9E,0xC9,0x7E,0x7A,0xC6,0x95,0x55,0x09, /* .....~z..U. */
  0x8B,0x19,0x5E,0x8B,0x26,0xCA,0xEB,0x68,0x8A,0x05,0x8F, /* ..^.&..h... */
  0x36,0xA5,0xA5,0x03,0xB8,0x9C,0xED,0x24,0x51,0x59,0x90, /* 6......$QY. */
  0xF6,0xC5,0x7D,0xB5,0xAD,0xAF,0xF6,0x3B,0x18,0xEF,0x3F, /* ..}....;..? */
  0xFF,0xFF,0x4E,0xDE,0x16,0x66,0x0B,0xAA,0x33,0x23,0xDD, /* ..N..f..3#. */
  0x9C,0x4E,0x6E,0x55,0x22,0x9D,0xA2,0x40,0xA6,0x36,0x31, /* .NnU"..@.61 */
  0x69,0xA5,0xE1,0xD9,0x7F,0xF7,0xC6,0xCC,0x48,0x00,0x0E, /* i.......H.. */
  0x90,0x16,0x00,0x0F,0xDE,0x6E,0x80,0x11,0x0C,0x9A,0x4F, /* .....n....O */
  0x56,0xDB,0x88,0xD3,0xB2,0x1C,0x00,0xE0,0x2E,0x3E,0xAC, /* V........>. */
  0xFF,0xF2,0x40,0xC0,0x1C,0xE5,0x19,0x13,0x31,0x4E,0xCD, /* ..@.....1N. */
  0x9E,0xC3,0x06,0x71,0x03,0x85,0xE5,0xB5,0x6D,0x88,0x50, /* ...q....m.P */
  0x8E,0x0E,0x17,0x3B,0x19,0xFB,0x4E,0x3B,0x99,0xEF,0x4C, /* ...;..N;..L */
  0x9E,0xF7,0x7B,0x31,0x7C,0x3C,0x5F,0xFF,0xF4,0xF8,0xE3, /* ..{1|<_.... */
  0x92,0x42,0x07,0x8E,0x83,0x8E,0x0F,0x05,0x08,0x91,0xA3, /* .B......... */
  0x16,0xE2,0xDF,0xB7,0x62,0x60,0x48,0x31,0x3C,0xFF,0xD4, /* ....b`H1<.. */
  0x9E,0x0C,0x68,0x00,0x77,0x54,0xE3,0x1E,0x05,0xC5,0xF8, /* ..h.wT..... */
  0xEA,0x8D,0x82,0x9D,0x08,0xA9,0x06,0x8D,0x1E,0x5D,0x7C, /* .........]| */
  0x7F,0x08,0xC0,0x50,0x45,0x42,0xD0,0x36,0xF8,0xB2,0x4D, /* ...PEB.6..M */
  0x53,0x0C,0x80,0x3B,0x4D,0xFF,0xF2,0x42,0xC0,0x2F,0x3C, /* S..;M..B./< */
  0x25,0x19,0x29,0xFE,0xBC,0x2E,0xC4,0xD0,0x99,0x4C,0x48, /* %.)......LH */
  0xB0,0x9C,0x49,0xD2,0x1A,0x2D,0x02,0xC2,0x79,0x69,0x16, /* ..I..-..yi. */
  0x92,0xA8,0xC5,0xAB,0x45,0x5A,0x68,0xE8,0x75,0x57,0xCD, /* ....EZh.uW. */
  0xF1,0xB9,0xAA,0x13,0x88,0xE4,0x87,0x42,0x15,0xB3,0x58, /* .......B..X */
  0xF5,0xA3,0x46,0xB1,0xCF,0xD3,0x59,0x7E,0xBA,0xB5,0xA7, /* ..F...Y~... */
  0x6B,0x0B,0x17,0x57,0x6B,0x5C,0x4A,0xCD,0x53,0x76,0x2A, /* k..Wk\J.Sv* */
  0x1D,0x28,0xC5,0x1C,0x76,0x5C,0xDD,0x0A,0x00,0x4B,0xC0, /* .(..v\...K. */
  0x1B,0xCA,0xA8,0xE9,0x81,0x5B,0xA6,0xDC,0xA4,0x59,0x13, /* .....[...Y. */
  0xFC,0xBA,0x8F,0x98,0x79,0x44,0x25,0xC9,0x35,0x38,0xCA, /* ....yD%.58. */
  0xFF,0xF2,0x40,0xC0,0xB9,0x7D,0x1A,0x13,0x79,0x6A,0xC8, /* ..@..}..yj. */
  0x3E,0xC4,0x46,0x94,0x8D,0x3C,0x67,0x85,0xB1,0xA8,0x89, /* >.F..<g.... */
  0xC0,0xF2,0xE6,0x2F,0x9D,0x7C,0xC9,0xB4,0xBE,0xCF,0xE1, /* .../.|..... */
  0x7D,0xFE,0x1F,0x03,0x00,0x12,0x84,0x72,0x8C,0xE7,0xD8, /* }......r... */
  0x5E,0xC9,0xA9,0x01,0xBA,0x9B,0xC4,0x10,0x5C,0x70,0x2E, /* ^.......\p. */
  0x6C,0x48,0xE7,0x8C,0x15,0x0B,0x06,0x01,0xE5,0xFF,0xFF, /* lH......... */
  0xD4,0x0D,0x00,0x0F,0xCE,0x58,0x95,0x61,0xA8,0x9E,0x7B, /* .....X.a..{ */
  0x19,0x98,0xB0,0xF0,0xC6,0x72,0x82,0xD5,0x27,0x06,0x47, /* .....r..'.G */
  0x41,0x22,0x0F,0x65,0x93,0xC9,0x8A,0x09,0x19,0x48,0x1B, /* A".e.....H. */
  0xBD,0xD6,0x64,0x1A,0xAC,0xFF,0xF2,0x42,0xC0,0xF1,0x11, /* ..d....B... */
  0x25,0x14,0x22,0x06,0xBC,0x0E,0xD4,0x4E,0x99,0x90,0xA8, /* %."....N... */
  0xD8,0xB7,0xAD,0x5D,0x3E,0xAF,0x6E,0xBE,0x66,0x83,0xA4, /* ...]>.n.f.. */
  0xE3,0xC2,0xE0,0x29,0x43,0x87,0x5F,0x4F,0x27,0x9C,0x2C, /* ...)C._O'., */
  0xD0,0x91,0xF3,0x87,0x9B,0x54,0xED,0xD1,0xB4,0xF3,0x39, /* .....T....9 */
  0x87,0x22,0x06,0x86,0x0D,0x71,0xE4,0x6F,0x2A,0x08,0x04, /* ."...q.o*.. */
  0xC0,0x03,0x2A,0xB1,0xE2,0x05,0x4D,0x64,0xA1,0x9C,0xA6, /* ..*...Md... */
  0x0D,0x41,0xA6,0xF2,0x7A,0xC1,0x30,0xC3,0x38,0x26,0x09, /* .A..z.0.8&. */
  0x50,0x08,0xC4,0xF6,0x30,0x0C,0xA6,0xA9,0x17,0x00,0x13, /* P...0...... */
  0x0C,0xDC,0xC4,0x2F,0x28,0xEB,0x3F,0xCD,0x7A,0x3D,0x2F, /* .../(.?.z=/ */
  0xFF,0xF2,0x40,0xC0,0x18,0x6F,0x2E,0x13,0xA1,0xF2,0xBC, /* ..@..o..... */
  0x36,0xCB,0x4E,0x99,0x6E,0xFC,0xEE,0xC5,0xF0,0xA0,0xB7, /* 6.N.n...... */
  0x92,0xD4,0xEE,0x79,0x7C,0x50,0x5D,0xE5,0x04,0x94,0xA9, /* ...y|P].... */
  0x76,0xCF,0x6C,0x70,0xDD,0x0D,0xD4,0xEE,0xED,0x98,0xE8, /* v.lp....... */
  0xC8,0x35,0x36,0x7A,0x0C,0x05,0x80,0x03,0xBC,0xBE,0x91, /* .56z....... */
  0x00,0x7C,0xAE,0x65,0xB8,0x91,0xA3,0x33,0xBA,0x68,0x60, /* .|.e...3.h` */
  0xD4,0x1A,0x66,0xF8,0x43,0xA0,0x20,0x89,0xE7,0x80,0xD8, /* ..f.C. .... */
  0x1E,0x4F,0xA0,0x04,0x60,0x06,0x0A,0xA4,0x91,0x24,0xFA, /* .O..`....$. */
  0x9F,0x57,0x53,0xF4,0x7A,0xDB,0x5F,0x56,0xE3,0x6E,0x0B, /* .WS.z._V.n. */
  0x8B,0x3A,0x1C,0xF9,0x5E,0xFF,0xF2,0x42,0xC0,0xB1,0x00, /* .:..^..B... */
  0x38,0x14,0x09,0xEE,0xB4,0x36,0xD3,0x4E,0x99,0xA4,0x78, /* 8....6.N..x */
  0x94,0x73,0xC4,0x66,0x30,0xF5,0xEA,0xDB,0xBA,0x67,0x67, /* .s.f0....gg */
  0x95,0x6B,0xAB,0x68,0x5D,0x08,0xA1,0x39,0x56,0xAB,0x1E, /* .k.h]..9V.. */
  0xD5,0x03,0xE8,0x01,0x70,0x00,0xB3,0x93,0x33,0x19,0x8C, /* ....p...3.. */
  0x61,0x8F,0xBB,0x5D,0x24,0x12,0x63,0xD3,0x4B,0x5D,0x91, /* a..]$.c.K]. */
  0x08,0x43,0x22,0x56,0x1A,0xC5,0x10,0x21,0x84,0xA8,0xEA, /* .C"V...!... */
  0x80,0xBF,0x16,0x8E,0x3D,0x46,0x18,0x9C,0x6E,0x9A,0x91, /* ....=F..n.. */
  0xE6,0xC9,0x6F,0xD2,0x7D,0x27,0xD7,0xE9,0x6B,0xFF,0x0A, /* ..o.}'..k.. */
  0x03,0x43,0x89,0xD5,0xBF,0x52,0x97,0x0A,0x25,0x95,0x0D, /* .C...R..%.. */
  0xFF,0xF2,0x40,0xC0,0xF5,0xC3,0x41,0x13,0x81,0xEE,0xA8, /* ..@...A.... */
  0x5E,0xD3,0x44,0x98,0xFC,0xCF,0x97,0xF9,0x58,0xB5,0x33, /* ^.D.....X.3 */
  0xB1,0x85,0x47,0x86,0xD7,0x98,0x01,0x3B,0xA3,0x4F,0x7E, /* ..G....;.O~ */
  0x04,0xA6,0xC3,0x39,0x21,0x70,0x27,0x62,0xB5,0x18,0x10, /* ...9!p'b... */
  0x09,0x99,0x00,0x8B,0x7E,0xF2,0xBF,0x52,0x18,0x26,0x30, /* ....~..R.&0 */
  0x1C,0xB0,0x01,0x49,0x30,0xE0,0xC3,0x11,0x46,0x05,0xCC, /* ...I0...F.. */
  0x49,0x14,0x28,0xB2,0xED,0x4B,0x57,0x5A,0x2F,0xB7,0x46, /* I.(..KWZ/.F */
  0x63,0x34,0xD2,0xDA,0x9F,0x56,0x32,0xB7,0xA2,0x25,0xFF, /* c4...V2..%. */
  0x94,0x28,0x33,0x7F,0x3B,0xC4,0x50,0xEC,0xB1,0xE2,0x26, /* .(3.;.P...& */
  0xA1,0xB7,0x07,0x7F,0xFB,0xFF,0xF2,0x42,0xC0,0x67,0x6A, /* .......B.gj */
  0x4C,0x13,0xF9,0x6A,0x90,0x7E,0xDB,0x44,0x94,0x3F,0xFF, /* L..j.~.D.?. */
  0x14,0xD6,0x2A,0xFF,0xFF,0xC1,0x34,0x8C,0x48,0x22,0x00, /* ..*...4.H". */
  0x06,0x8F,0x21,0xFD,0x64,0x60,0x04,0x92,0x42,0xEA,0x74, /* ..!.d`..B.t */
  0x32,0x37,0xAA,0x5A,0x9F,0x67,0x01,0x8B,0x3F,0x37,0x31, /* 27.Z.g..?71 */
  0xDD,0x06,0x3C,0x01,0x34,0x30,0xE0,0x5C,0x78,0x78,0xCB, /* ..<.40.\xx. */
  0xD6,0xF1,0x31,0x8A,0x69,0x61,0x93,0x92,0x42,0xCE,0x4B, /* ..1.ia..B.K */
  0xC5,0x02,0x4E,0x73,0xC6,0x24,0x30,0xCD,0x08,0x66,0xC6, /* ..Ns.$0..f. */
  0x35,0xAB,0xA2,0x3D,0x2F,0xB3,0xBD,0x34,0x87,0x13,0xEE, /* 5..=/..4... */
  0x71,0x45,0x68,0xFA,0xEA,0x05,0x84,0x41,0x36,0x4C,0x9A, /* qEh....A6L. */
  0xFF,0xF2,0x40,0xC0,0xC9,0x92,0x56,0x13,0xD0,0x6E,0x70, /* ..@...V..np */
  0x54,0xD3,0xCC,0x28,0x06,0xD7,0x0E,0xA4,0x1D,0x9C,0x9D, /* T..(....... */
  0xD9,0xA9,0x88,0x7B,0xB5,0xA3,0x56,0xB7,0x4B,0x4B,0x5A, /* ...{..V.KKZ */
  0x9B,0x2C,0xA9,0xAD,0x6F,0x99,0x6C,0xC0,0x4C,0x14,0x14, /* .,..o.l.L.. */
  0xEF,0xB4,0x20,0x91,0x5F,0xBC,0x81,0x41,0x41,0x5D,0xD4, /* .. ._..AA]. */
  0x20,0xBD,0x05,0x1A,0x6F,0xE2,0x68,0x56,0x41,0x41,0x57, /*  ...o.hVAAW */
  0xF9,0xBF,0x89,0x82,0x8E,0xC7,0x8F,0x0A,0x0A,0x09,0x37, /* ..........7 */
  0xF1,0x05,0x0A,0x0A,0x0A,0x0A,0x09,0x05,0x37,0xFF,0x10, /* ........7.. */
  0x50,0x50,0x53,0x65,0xFF,0xFF,0xFD,0x75,0xDF,0xFF,0xFF, /* PPSe...u... */
  0x68,0x4F,0xFF,0x84,0x70,0xFF,0xF2,0x42,0xC0,0x27,0x50, /* hO..p..B.'P */
  0x5F,0x17,0xE8,0x82,0x3C,0x11,0x58,0x18,0x01,0x55,0x48, /* _...<.X..UH */
  0xBC,0x52,0xFC,0x4A,0x4C,0x3C,0xD5,0xF6,0x11,0x2D,0xBF, /* .R.JL<...-. */
  0xEA,0x03,0x5C,0x57,0x29,0xBF,0xC3,0x75,0x1C,0xE6,0xDD, /* ..\W)..u... */
  0xBF,0xED,0xEF,0xD0,0x98,0x77,0x71,0x95,0x73,0xFF,0xED, /* .....wq.s.. */
  0x54,0xBE,0xD5,0xEE,0xAE,0xC2,0xD5,0x0B,0xFF,0xF1,0x97, /* T.......... */
  0x8A,0xE4,0x42,0x09,0x99,0xB1,0xEA,0x94,0xDC,0x78,0xB5, /* ..B......x. */
  0x34,0x0F,0xF1,0x8F,0xFC,0x15,0xF6,0xFA,0xB1,0x47,0xA9, /* 4........G. */
  0x6C,0x67,0x43,0x8B,0xF2,0x76,0x22,0xED,0xDA,0x85,0xBA, /* lgC..v".... */
  0x2F,0xC7,0xF9,0xCF,0xFC,0xDB,0x46,0x2E,0x50,0x0A,0x84, /* /.....F.P.. */
  0xFF,0xF2,0x40,0xC0,0xC6,0x4A,0x59,0x28,0x2B,0x19,0xE0, /* ..@..JY(+.. */
  0x01,0x89,0x78,0x00,0x52,0x85,0x3C,0x8E,0x54,0x9A,0x48, /* ..x.R.<.T.H */
  0x5A,0x72,0x32,0x94,0xBF,0x43,0x4F,0x24,0x53,0x4B,0xEC, /* Zr2..CO$SK. */
  0x4B,0x99,0x0E,0x66,0x1F,0xFF,0xCE,0x7F,0xFF,0x3F,0x10, /* K..f.....?. */
  0xAE,0x82,0x62,0x71,0x34,0x18,0x59,0x9B,0x51,0xC7,0x59, /* ..bq4.Y.Q.Y */
  0xCE,0xEE,0xA5,0xFE,0x02,0xBB,0x30,0x91,0x49,0xD5,0x4B, /* ......0.I.K */
  0xF3,0xDC,0x9A,0xA9,0x57,0x8E,0x72,0x10,0xC0,0x5D,0x60, /* ....W.r..]` */
  0x67,0xFC,0x7D,0xD6,0xBA,0xDD,0xB3,0x8B,0x5A,0x0A,0x4C, /* g.}.....Z.L */
  0x41,0x4D,0x45,0x33,0x2E,0x39,0x33,0xAA,0xAA,0xAA,0xAA, /* AME3.93.... */
  0xAA,0xAA,0xAA,0xAA,0xAA,0x54,0x41,0x47,0x48,0x65,0x6C, /* .....TAGHel */
  0x6C,0x6F,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20, /* lo          */
  0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20, /*             */
  0x20,0x20,0x20,0x20,0x20,0x50,0x61,0x6E,0x75,0x2D,0x4B, /*      Panu-K */
  0x72,0x69,0x73,0x74,0x69,0x61,0x6E,0x20,0x50,0x6F,0x69, /* ristian Poi */
  0x6B,0x73,0x61,0x6C,0x6F,0x20,0x20,0x20,0x20,0x20,0x20, /* ksalo       */
  0x20,0x20,0x56,0x53,0x44,0x53,0x50,0x20,0x54,0x65,0x73, /*   VSDSP Tes */
  0x74,0x69,0x6E,0x67,0x20,0x20,0x20,0x20,0x20,0x20,0x20, /* ting        */
  0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20, /*             */
  0x20,0x20,0x20,0x4D,0x50,0x33,0x20,0x48,0x65,0x6C,0x6C, /*    MP3 Hell */
  0x6F,0x2C,0x20,0x57,0x6F,0x72,0x6C,0x64,0x21,0x20,0x20, /* o, World!   */
  0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20,0x20, /*             */
  0x00, /* . */
};

void setup() {
  pinMode(MP3_DREQ, INPUT);
  pinMode(MP3_XCS, OUTPUT);
  pinMode(MP3_XDCS, OUTPUT);
  //Note that even if you're not using the SS pin, it must remain set as an output;
  //otherwise, the SPI interface can be put into slave mode, rendering the library inoperative.
  pinMode(10, OUTPUT);//the SS of the SPI interface on the arduino board
  SPI.begin();
  SPI.setBitOrder(MSBFIRST);
  SPI.setDataMode(SPI_MODE0);
  //max SDI clock freq = CLKI/7 and (datasheet) CLKI = 36.864, hence max clock = 5MHz
  //SPI clock arduino = 16MHz. 16/ 4 = 4MHz -- ok!
 
  //initialize chip
  Mp3DeselectControl();
  Mp3DeselectData();
  Mp3SetVolume(0xff,0xff); //Declick: Immediately switch analog off
   /* Declick: Slow sample rate for slow analog part startup */
  Mp3WriteRegister(SPI_AUDATA, 0, 10); /* 10 Hz */
  delay(100);
  /* Switch on the analog parts */
  Mp3SetVolume(0xfe,0xfe);
  Mp3WriteRegister (SPI_AUDATA, 31, 64); /* 8kHz */
  Mp3SetVolume(20,20); // Set initial volume (20 = -10dB)
  Mp3SoftReset();
}

void InitMicrocontroller(){
  SPI.setClockDivider(SPI_CLOCK_DIV64);//slow SPI bus speed
  SPI.transfer(0xFF);
}

void SPIInit(){
  SPI.setClockDivider(SPI_CLOCK_DIV4); //basically just set fast SPI bus speed
}

void loop(){
 
  unsigned char *p;
  unsigned int i;
 
  InitMicrocontroller();
  SPIInit();
 
  p = &HelloMP3[0]; // Point "p" to the beginning of array
    while (p <= &HelloMP3[sizeof(HelloMP3)-1]) {
      while (!digitalRead(MP3_DREQ)) {
       // MP3 buffer is full, time to do something else...
       SPIWait(); // Wait until SPI transfer is completed
       Mp3DeselectData(); // Release the SDI bus
       // You can do something else here, the bus is free...
       // Maybe set the volume or whatever...
      }
      Mp3SelectData(); // Pull XDCS low
      SPI.transfer(*p++); // Send SPI byte
      // You can actually send 32 bytes here before checking for DREQ again
    }
   
    // End of file - send 2048 zeros before next file
    Mp3SelectData();
    for (i=0; i<2048; i++) {
      while (!digitalRead(MP3_DREQ)); // wait here until DREQ is high again
      SPI.transfer(0);     
    }
    SPIWait(); // Wait until SPI transfer is completed
    Mp3DeselectData();
    Mp3SoftReset();
}
RuiAlves
User
 
Posts: 9
Joined: Tue 2010-10-05 18:42

Re: Audible "Hello" example for VS1003B + Microcontroller

Postby Panu » Thu 2010-11-04 14:59

Dear Rui,

Rui, you've really made me happy today. Thanks for sharing your code!

As a small reward, we've decided to give you a copy of the "First Steps with VS1053" book.
I'll write you an e-mail to ask for a delivery address.

-Panu
Info: Line In and Line Out, VS1000 User interface, Overlay howto, Latest VSIDE, MCU Howto, Youtube
Panu-Kristian Poiksalo, VLSI Solution Oy
User avatar
Panu
VLSI Staff. Currently on holiday.
 
Posts: 1481
Joined: Tue 2010-06-22 13:43

Re: Audible "Hello" example for VS1003B + Microcontroller

Postby RuiAlves » Tue 2010-11-16 5:37

Many thanks Panu, I received the book today! I didn't realize I was talking with the author ;-)

Cheers,
Rui
RuiAlves
User
 
Posts: 9
Joined: Tue 2010-10-05 18:42

Re: Audible "Hello" example for VS1003B + Microcontroller

Postby Panu » Tue 2010-11-16 12:37

Hi!

Well, someone has to write these books! ;)

Good luck!

-Panu
Info: Line In and Line Out, VS1000 User interface, Overlay howto, Latest VSIDE, MCU Howto, Youtube
Panu-Kristian Poiksalo, VLSI Solution Oy
User avatar
Panu
VLSI Staff. Currently on holiday.
 
Posts: 1481
Joined: Tue 2010-06-22 13:43

Audible Hello for VS1053 and generic 8051 (AT89C4051)

Postby Panu » Sun 2010-11-21 11:24

Hi! Here's another version of the audible hello, this time for a generic 8051 microcontroller (no hardware SPI port). It works for example with AT89C4051 so it should work with just about any 8051 microcontroller.

This code makes a simple software SPI port and sends the SCI commands and SDI data with it. Note that the software SPI port is not fast enough to send high bitrate MP3, but it is useful for configuring the VS1053 and testing.

Edit: There is a bug in the software SPI Port function "SpiTransfer()" in the "hello.c" file!! Data input (register reads) give incorrect values with the way the function was written. The correct way is:
Code: Select all
// Shift 8 bits in and out using a software SPI port
unsigned char SpiTransfer (unsigned char outdata) {
  unsigned char b=0;
  unsigned char indata=0;
  for (b=0; b<8; b++) {
    if (outdata & 0x80) { // Leftmost bit first
      OUT_SET_HIGH(PIN_MOSI);
    } else {
      OUT_SET_LOW(PIN_MOSI);
    }
    outdata <<= 1; // Shift outdata bits left
    OUT_SET_HIGH(PIN_SCK); // Clock high
    indata <<= 1; // Shift indata bits left
    if (IN_IS_HIGH(PIN_MISO)) {
      indata |= 1; // Set rightmost bit high
    }   
    OUT_SET_LOW(PIN_SCK); // Clock low
  }
  return indata; // Return the result byte to caller
}       

Have fun!
-Panu
Attachments
AuHello.hex
Intel HEX file for 8051. Pins: P1.1 DREQ, P1.2 XDCS, P1.3 XRESET, P1.4 XCS P1.5 moSI, P1.6 miSO, P1.7 SCK
(7.58 KiB) Downloaded 345 times
at89c4051-sdcc.h
Microcontroller register definitions for AT89C4051 and SDCC compiler
(2.33 KiB) Downloaded 382 times
hello.c
Audible Hello for VS1053 and AT89C4051 or generic 8051 MCU
(18.38 KiB) Downloaded 471 times
Last edited by Panu on Mon 2012-01-02 16:15, edited 3 times in total.
Reason: Noticed a bug in the software SPI port when reading SCI registers...
Info: Line In and Line Out, VS1000 User interface, Overlay howto, Latest VSIDE, MCU Howto, Youtube
Panu-Kristian Poiksalo, VLSI Solution Oy
User avatar
Panu
VLSI Staff. Currently on holiday.
 
Posts: 1481
Joined: Tue 2010-06-22 13:43

Re: Audible "Hello" example for VS1003B + Microcontroller

Postby russdx » Mon 2011-02-07 15:23

thanks for these examples, they are the most cleanest and well commented examples for these chips i have come across so far. VERY useful for people like me just starting to use these decoders :)

Thanks again :)
russdx
Senior User
 
Posts: 43
Joined: Mon 2011-02-07 15:21

Re: Audible "Hello" example for VS1003B + Microcontroller

Postby Panu » Fri 2011-02-11 14:29

Dear russdx,

That's great! Thank you.
Good luck with your project!

-Panu
Info: Line In and Line Out, VS1000 User interface, Overlay howto, Latest VSIDE, MCU Howto, Youtube
Panu-Kristian Poiksalo, VLSI Solution Oy
User avatar
Panu
VLSI Staff. Currently on holiday.
 
Posts: 1481
Joined: Tue 2010-06-22 13:43

Re: Audible "Hello" example for VS1003B + Microcontroller

Postby jc000 » Sun 2011-02-13 20:39

Hi, there. I just brought up a Sparkfun VS1033D board (BOB-08792) last night on Arduino. Thanks to Panu and Rui for the hello world code, which provided an excellent reference when troubleshooting my own.

One thing I would recommend for Rui is to clean up "SPIWait". In Panu's example, it waits for the SPI transfer to complete, which is necessary because SPDAT=(c) is non-blocking. On Arduino, SPI.transfer() blocks on SPSR.SPIF, so no further waiting is needed. Since these are the best getting-started examples out there, it will help to have them as clean as possible for other people learning this hardware.

As an aside, I am affected by the elsewhere-documented problems with the floating TEST pin with this board, so I have to work around a flaky DREQ signal. For CBR MP3 streams, I manage the delay manually based on bitrate, which is good enough to make plenty of progress. I am going to ask Sparkfun to make the blue-wire fix themselves and send me a replacement. We'll see how that goes!
jc000
Beginning User
 
Posts: 3
Joined: Sun 2011-02-13 20:15

Re: Audible "Hello" example for VS1003B + Microcontroller

Postby Jeremyvnc » Tue 2011-03-01 6:44

So, I've tried this code on both the breakout board from sparkfun like jc00 and a breakout board from MDFly.com (which has the XTest pulled high and all GPIOs pulled low) connected to an arduino. Both boards perform the same. They both just beep over and over again. Any ideas? I suppose it could just be zipping through the array if it never sees the DREQ pin go low but not sure why it wouldn't. I'm planning on taking my circuit to work tomorrow to see what the o-scope says but just wanted to see if you all had any thoughts being the masters that you are :D.

FYI, I'm using the arduino in 5V mode, I have translated the voltage to 3.3V on the MISO, CLK, CS, and DCS pins using voltage divider. I have checked my wiring so many times but I just cannot make either board perform. Even sine test is splotchy (takes a long time to turn on).

Please help me.
-Jeremy
Jeremyvnc
User
 
Posts: 18
Joined: Thu 2011-02-24 5:32

Next

Return to Microcontroller Software

Who is online

Users browsing this forum: No registered users

cron